Nightclub Epoxy that survives the room
Spilled drinks, heels and blackout lighting. Most jobs need one day of our time and none of yours.
Mops clean at 3am and looks right at 10pm.
What we actually install
Dark seamless build with grip where it is wet.
Concrete varies street to street around here, so we check. Dense crowds and constant liquid.
Talk to us about this floor or call 601-319-9619.
How the day runs
Grind
Dark seamless build with grip where it is wet.
Build
Dense crowds and constant liquid.
Cure
A typical garage is a one day install. You are walking on it that evening.
What the install actually looks like
The slab sets the spec, not the brochure.
Every job starts the same way, with the slab itself. We turn up with the grinder and the extraction first, and the first hour is dust and noise rather than anything that looks like progress. Dark seamless build with grip where it is wet.
Once the slab is open and clean we chase any cracks, fill them, and grind those flat. Then the primer goes down, and from that point the day is a sequence with cure windows in it rather than a job you can rush. One day, one crew, then cure time does the rest.
Kevin built the company in 2021 around doing the work they promised. The crew has not changed. That matters on a nightclub epoxy job because the person who decided the spec is the person holding the squeegee, so nothing gets lost between the quote and the floor.
Choosing somebody to do our Floors was a hard decision but I am so happy we picked ICM coating masters. The results are beautiful and The time and effort put into the work was amazing.Verified review
Other retail floors we coat
The slab decides the spec.
What we find under a nightclub epoxy job
Where a floor has been patched repeatedly with different products, each patch behaves differently under a grinder and under resin. Sometimes the right call is removing the patches entirely.
A slab poured in sections often has slight height differences at the seams. Those get ground flat rather than coated over, because a coating follows the shape it is laid on.
The system we specify
The chip blend changes how a floor hides dirt. Multi-tone blends with some dark in them stay looking clean far longer than a single pale colour.
Everything we install is a system that has been tested as a system. That is the practical value of working to a manufacturer spec instead of improvising.
Specified from the load, not a brochure.
A retail floor is doing two jobs at once
It has to survive the traffic and it has to look like part of the fit-out. Those pull in opposite directions. The most durable finishes are textured and dark, and the finishes that photograph well are smooth and bright. Where a floor lands between those is a decision worth making deliberately rather than by default.
The practical constraint in retail is almost always time. You cannot close for a week. That means phasing the work, or working nights, or using a fast-cure system that is walkable before you open. All three are possible and they cost differently, so it is worth saying up front which one matters most to you.
A standard install is one day of work and two days of patience.
What we plan around
Spilled drinks, heels and blackout lighting.
What this floor has to put up with
Dense crowds and constant liquid. Dark seamless build with grip where it is wet. That combination is what we specify against, and it is why a nightclub epoxy job is quoted from the room rather than from a rate card.
Mops clean at 3am and looks right at 10pm. One day down for most homes. Commercial work is phased to your hours.
Living with the floor afterwards
If a crack appears in the slab years later, that is the concrete moving, not the coating failing. It can be chased and repaired without redoing the floor.
Do not drag steel across it. Lift it, or put something under it.
We work out of Laurel and cover roughly a hundred miles in every direction. That takes in Jones County, Rankin, Simpson and Lamar to the north and west, the whole Mississippi coast from Bay St. Louis through Biloxi to Pascagoula, across into Baldwin and Mobile County in Alabama, and west to St. Tammany Parish. See the areas we cover.
Questions we get asked
How long before we can use the room again?
Most jobs need one day of our time and none of yours.
How much of the job is preparation?
Dark seamless build with grip where it is wet. Moisture gets tested before resin gets opened.
How durable is it in practice?
Dense crowds and constant liquid. We specify the build thickness against the actual use, not a standard sheet.
Are you working in Alabama and Louisiana too?
Yes. We cover south Mississippi, the coast, coastal Alabama and St. Tammany Parish, roughly a hundred miles out from Laurel.
Who runs the job?
Four names, one crew. Kevin Garner built the company in 2021 to pass it on.
Can I see the colour before deciding?
Yes. We bring the chip deck out and you pick the blend against your own light and your own walls. Colours read differently under LED, under a skylight and under a garage door that is half open, so choosing off a photograph is how people end up disappointed.
What if there is already a coating on it?
Control joints and cracks are not the same thing and get treated differently. A control joint is doing a job and needs to stay flexible. A crack is failure and gets chased out, filled with a rigid polyurea and ground flat before anything goes over it.
What should I avoid doing to it?
Sunlight through a garage door will fade a cheap floor unevenly along the door line. UV-stable topcoats exist precisely for that.
What makes the difference long term?
We install Duraflex systems. The certification matters less than what it means in practice, which is that the product data is real, the cure windows are tested, and there is a manufacturer standing behind the spec rather than a generic resin bought on price.
Call and describe the floor. We will know most of it from that.
This is a family crew. Kevin founded it in 2021 and works alongside Aaron, Kyler and Averie. Serving Laurel and south Mississippi, the Gulf Coast, coastal Alabama and St. Tammany Parish. See finished floors or get in touch.