Tattoo Shop Epoxy that survives the room
Sterile requirements and ink. Most houses are done inside a day, then 12 hours to foot traffic.
Reads sterile because it is.
What we actually install
Non-porous seamless build, wipes to clean.
A coating is only as good as the grind under it. Stations, chairs and strict hygiene.
Talk to us about this floor or call 601-319-9619.
How the day runs
Grind
Non-porous seamless build, wipes to clean.
Build
Stations, chairs and strict hygiene.
Cure
The whole system goes down in one visit on most homes.
What the install actually looks like
Every job starts the same way, with the slab itself.
Preparation is the part customers never see and always pay for twice if it is skipped. We turn up with the grinder and the extraction first, and the first hour is dust and noise rather than anything that looks like progress. Non-porous seamless build, wipes to clean.
Once the slab is open and clean we chase any cracks, fill them, and grind those flat. Then the primer goes down, and from that point the day is a sequence with cure windows in it rather than a job you can rush. We are in and out in a day on most garages, then the floor cures.
The reason quality holds is that the family name is on every job. That matters on a tattoo shop epoxy job because the person who decided the spec is the person holding the squeegee, so nothing gets lost between the quote and the floor.
Aaron and his crew did a fantastic job, friendly and professional.Verified review
Other trades floors we coat
The slab decides the spec.
What we find under a tattoo shop epoxy job
Commercial slabs that have been in service take oil deep into the pores. Surface degreasing does not reach it, and resin will not bond through it. We grind it out, and where contamination runs deep we prime with something built to tolerate it.
Slabs around Laurel and down toward the coast are mostly 1970s to 1990s pours, and they were finished hard. A hard-troweled surface has almost no porosity left, which is why paint peels off it in sheets. Grinding opens that surface back up so resin can key into the concrete instead of sitting on top of it.
The system we specify
Pigments are not all equally stable. Reds and yellows fade fastest under UV, so exterior work uses pigments chosen for it rather than the same colours we would use in a closed garage.
Pigments are not all equally stable. Reds and yellows fade fastest under UV, so exterior work uses pigments chosen for it rather than the same colours we would use in a closed garage.
Specified from the load, not a brochure.
Small floors, specific problems
A small commercial floor is not a scaled down warehouse. The problems are concentrated. One wet area, one chair that rotates in the same spot every day, one chemical that gets spilled constantly. Specifying the whole room for the worst square metre is usually cheaper than specifying it for the average and repairing the worst part later.
The other reality is that these rooms cannot close. A barbershop or a salon loses its income the day it shuts. That pushes the work to a single overnight or weekend install with a fast-cure system, which is entirely doable as long as it is planned that way from the start rather than discovered halfway through.
We grind, coat and topcoat in one visit on most residential jobs.
How we handle small commercial work
Sterile requirements and ink.
What this floor has to put up with
Stations, chairs and strict hygiene. Non-porous seamless build, wipes to clean. That combination is what we specify against, and it is why a tattoo shop epoxy job is quoted from the room rather than from a rate card.
Reads sterile because it is. Residential floors are usually a one day job start to finish.
Living with the floor afterwards
A coated floor can be repaired in place. Damage gets ground back locally, rebuilt and blended, which is not possible with tile or with polished concrete.
Expect the finish to look the same in five years if it is looked after. That is the point of specifying properly rather than cheaply.
Laurel is home, and from here we reach Hattiesburg, Jackson, the Gulf Coast, coastal Alabama and the north shore of Lake Pontchartrain comfortably. Coast jobs and Baldwin County work are a normal week for us. See the areas we cover.
Questions we get asked
How quickly can this be done?
Most houses are done inside a day, then 12 hours to foot traffic.
Do you grind the floor first?
Non-porous seamless build, wipes to clean. We start by finding the cracks nobody mentioned.
What kind of wear can it take?
Stations, chairs and strict hygiene. We specify the build thickness against the actual use, not a standard sheet.
Where abouts do you work?
Yes. We cover south Mississippi, the coast, coastal Alabama and St. Tammany Parish, roughly a hundred miles out from Laurel.
Who am I actually hiring?
Kevin founded ICM Coating Masters in 2021 and still runs jobs himself.
Can I see the colour before deciding?
Yes. We bring the chip deck out and you pick the blend against your own light and your own walls. Colours read differently under LED, under a skylight and under a garage door that is half open, so choosing off a photograph is how people end up disappointed.
What if the floor is damp?
Gulf Coast concrete carries moisture. Slabs poured on sand without a vapour barrier wick water up through the mix continuously, and that vapour pressure is what lifts a coating months after it looked perfect. We test for it before quoting, because the honest answer sometimes is a moisture-tolerant system rather than standard epoxy.
Do I need to reseal it?
A coated floor can be repaired in place. Damage gets ground back locally, rebuilt and blended, which is not possible with tile or with polished concrete.
What stops it peeling?
Everything we install is a system that has been tested as a system. That is the practical value of working to a manufacturer spec instead of improvising.
Pick up the phone and ask. No pressure either way.
Kevin built the company in 2021 around doing the work they promised. The crew has not changed. Serving Laurel and south Mississippi, the Gulf Coast, coastal Alabama and St. Tammany Parish. See finished floors or get in touch.