Indoor Sports Facility Epoxy that survives the room
Big spans, line marking and hard use. One visit, one day, then 48 hours before the car goes back on.
Lines that do not wear off in a season.
What we actually install
Large-format build with inlaid line marking.
We test the slab before we promise a finish. Running, equipment and spectator traffic.
Talk to us about this floor or call 601-319-9619.
How the day runs
Grind
Large-format build with inlaid line marking.
Build
Running, equipment and spectator traffic.
Cure
One day down for most homes. Commercial work is phased to your hours.
What the install actually looks like
Prep is most of the work and all of the reason coatings last.
Moisture gets tested before resin gets opened. We turn up with the grinder and the extraction first, and the first hour is dust and noise rather than anything that looks like progress. Large-format build with inlaid line marking.
Once the slab is open and clean we chase any cracks, fill them, and grind those flat. Then the primer goes down, and from that point the day is a sequence with cure windows in it rather than a job you can rush. A standard install is one day of work and two days of patience.
Kevin founded ICM Coating Masters in 2021 and still runs jobs himself. That matters on a indoor sports facility epoxy job because the person who decided the spec is the person holding the squeegee, so nothing gets lost between the quote and the floor.
Choosing somebody to do our Floors was a hard decision but I am so happy we picked ICM coating masters. The results are beautiful and The time and effort put into the work was amazing.Verified review
Other fitness floors we coat
The slab decides the spec.
What we find under a indoor sports facility epoxy job
Concrete keeps moving for years after it is poured, and it moves more near the coast where the ground is wet and sandy. That is why we detail edges and joints rather than laying one continuous rigid sheet and hoping.
Some floors do not need coating at all. If the slab is sound and the use is light, polishing or sealing the concrete itself is cheaper and lasts longer. We will say so.
The system we specify
Slip resistance comes from profile, not from an additive stirred in at the end. Where a floor will be wet we build the texture in with graded aggregate and we tell you how it will feel underfoot.
Moisture-tolerant primers exist for a reason and cost more for a reason. On a damp slab they are the difference between a floor and a warranty claim.
Specified from the load, not a brochure.
Impact is a different problem from wear
Most floors are specified for abrasion, which is a slow surface problem. A gym floor has to survive impact, which is a sudden structural one. A dropped barbell delivers its whole energy into a few square inches, and a thin rigid coating over concrete will spall at that point no matter how hard the topcoat is.
The answer is build thickness in the drop zones and a topcoat with some flexibility rather than maximum hardness. Under matting the coating still matters, because sweat and cleaning water get under mats and sit there. A sealed non-porous floor under the mats is what stops that becoming a smell you cannot find the source of.
One day, one crew, then cure time does the rest.
What we specify for training floors
Big spans, line marking and hard use.
What this floor has to put up with
Running, equipment and spectator traffic. Large-format build with inlaid line marking. That combination is what we specify against, and it is why a indoor sports facility epoxy job is quoted from the room rather than from a rate card.
Lines that do not wear off in a season. Single day turnaround on typical residential slabs.
Living with the floor afterwards
Hot tyre pickup is a failure mode of cheap coatings, not of a properly installed flake and polyaspartic build. You can park on it hot without lifting the finish.
Pressure washing exterior coated concrete is fine at sensible pressure. Holding a turbo nozzle in one place is not.
The service area runs from Jones County out to the coast and along it. Gulfport, Biloxi, Ocean Springs and Pascagoula in Mississippi, Gulf Shores and Foley in Alabama, Covington and Slidell in Louisiana. See the areas we cover.
Questions we get asked
How long will my floor be out of use?
One visit, one day, then 48 hours before the car goes back on.
What happens to the slab before you coat it?
Large-format build with inlaid line marking. Every job starts the same way, with the slab itself.
Will it stand up to the traffic here?
Running, equipment and spectator traffic. We specify the build thickness against the actual use, not a standard sheet.
Do you come out to the coast?
Yes. We cover south Mississippi, the coast, coastal Alabama and St. Tammany Parish, roughly a hundred miles out from Laurel.
Do you use subcontractors?
This is a family crew. Kevin founded it in 2021 and works alongside Aaron, Kyler and Averie.
Can I see the colour before deciding?
Yes. We bring the chip deck out and you pick the blend against your own light and your own walls. Colours read differently under LED, under a skylight and under a garage door that is half open, so choosing off a photograph is how people end up disappointed.
Is an old slab a problem?
A lot of the slabs we open up have been sealed at some point with an acrylic nobody remembers. It reads as clean concrete until the diamonds hit it and the surface loads up. That is a full mechanical removal, not a light scuff, and it changes the day.
How do I look after it?
In a commercial kitchen the cleaning routine is the maintenance plan, and the floor is specified around the chemistry you already use.
Why not just use floor paint?
Everything we install is a system that has been tested as a system. That is the practical value of working to a manufacturer spec instead of improvising.
We are happy to look at it and tell you what we would do.
This company exists to be passed down, which changes how carefully you work. Serving Laurel and south Mississippi, the Gulf Coast, coastal Alabama and St. Tammany Parish. See finished floors or get in touch.