Arcade Epoxy that survives the room
Spilled drinks under cabinets nobody moves. Most of our residential installs are complete within a single working day.
Cleans without moving every machine.
What we actually install
Seamless dark build that hides wear.
First we make the slab ready, then the finish is the easy part. Dense foot traffic and sticky spills.
Talk to us about this floor or call 601-319-9619.
How the day runs
Grind
Seamless dark build that hides wear.
Build
Dense foot traffic and sticky spills.
Cure
We are in and out in a day on most garages, then the floor cures.
What the install actually looks like
No two slabs in Jones County behave the same way.
Moisture gets tested before resin gets opened. We turn up with the grinder and the extraction first, and the first hour is dust and noise rather than anything that looks like progress. Seamless dark build that hides wear.
Once the slab is open and clean we chase any cracks, fill them, and grind those flat. Then the primer goes down, and from that point the day is a sequence with cure windows in it rather than a job you can rush. Most houses are done inside a day, then 12 hours to foot traffic.
Since 2021 this has been Kevin, Aaron, Kyler and Averie. No subcontractors sent in your place. That matters on a arcade epoxy job because the person who decided the spec is the person holding the squeegee, so nothing gets lost between the quote and the floor.
Aaron and his crew did a fantastic job, friendly and professional.Verified review
Other fitness floors we coat
The slab decides the spec.
What we find under a arcade epoxy job
Moisture, contamination and surface profile are the three things that decide whether a floor lasts. Colour is the easy part and the only part most people ask about.
Exterior concrete has UV and thermal cycling on top of everything else. Materials that are fine indoors amber and chalk outside, so exterior work gets a UV-stable topcoat as standard.
The system we specify
Everything we install is a system that has been tested as a system. That is the practical value of working to a manufacturer spec instead of improvising.
The chip blend changes how a floor hides dirt. Multi-tone blends with some dark in them stay looking clean far longer than a single pale colour.
Specified from the load, not a brochure.
Impact is a different problem from wear
Most floors are specified for abrasion, which is a slow surface problem. A gym floor has to survive impact, which is a sudden structural one. A dropped barbell delivers its whole energy into a few square inches, and a thin rigid coating over concrete will spall at that point no matter how hard the topcoat is.
The answer is build thickness in the drop zones and a topcoat with some flexibility rather than maximum hardness. Under matting the coating still matters, because sweat and cleaning water get under mats and sit there. A sealed non-porous floor under the mats is what stops that becoming a smell you cannot find the source of.
One day, one crew, then cure time does the rest.
What we specify for training floors
Spilled drinks under cabinets nobody moves.
What this floor has to put up with
Dense foot traffic and sticky spills. Seamless dark build that hides wear. That combination is what we specify against, and it is why a arcade epoxy job is quoted from the room rather than from a rate card.
Cleans without moving every machine. Residential floors are usually a one day job start to finish.
Living with the floor afterwards
The honest maintenance answer is that there is almost none, and that is most of why people choose it.
Warehouse floors want a scrubber with the right pad, not the most aggressive one available.
From Laurel we cover south Mississippi, the coast, coastal Alabama and St. Tammany Parish. If you are inside about a hundred miles, we will come and look at the slab. See the areas we cover.
Questions we get asked
How long will my floor be out of use?
Most of our residential installs are complete within a single working day.
What happens to the slab before you coat it?
Seamless dark build that hides wear. The slab sets the spec, not the brochure.
Will it stand up to the traffic here?
Dense foot traffic and sticky spills. We specify the build thickness against the actual use, not a standard sheet.
Do you come out to the coast?
Yes. We cover south Mississippi, the coast, coastal Alabama and St. Tammany Parish, roughly a hundred miles out from Laurel.
Do you use subcontractors?
Kevin started ICM in 2021. The team that keeps it going is Aaron Garner, Kyler Welch and Averie Garner.
Can I see the colour before deciding?
Yes. We bring the chip deck out and you pick the blend against your own light and your own walls. Colours read differently under LED, under a skylight and under a garage door that is half open, so choosing off a photograph is how people end up disappointed.
Is an old slab a problem?
Where a floor has been patched repeatedly with different products, each patch behaves differently under a grinder and under resin. Sometimes the right call is removing the patches entirely.
How do I look after it?
Maintenance is a dust mop and occasionally a neutral cleaner. No wax, no sealing, no annual reapplication. If someone tells you a coated floor needs yearly maintenance, they are describing their own product failing.
Why not just use floor paint?
Full flake broadcast means chip thrown to refusal, so the floor is a continuous layer of vinyl rather than a base coat with decoration on it. That is what gives the texture its grip and what stops the colour wearing through.
Talk it through with the people who will do the work.
Kevin built the company in 2021 around doing the work they promised. The crew has not changed. Serving Laurel and south Mississippi, the Gulf Coast, coastal Alabama and St. Tammany Parish. See finished floors or get in touch.