Concrete Grinding done in a day
Old adhesive, paint and trip-hazard high spots have to go before anything else happens. Most of our residential installs are complete within a single working day.
Usually booked as the first day of a coating job.
What we actually install
Diamond grinding with dust extraction, flattened and profiled ready to coat.
First we make the slab ready, then the finish is the easy part. This is the prep step every lasting floor depends on.
Talk to us about this floor or call 601-319-9619.
How the day runs
Grind
Diamond grinding with dust extraction, flattened and profiled ready to coat.
Build
This is the prep step every lasting floor depends on.
Cure
One day down for most homes. Commercial work is phased to your hours.
What the install actually looks like
We would rather spend the morning grinding than come back in a year.
We test the slab before we promise a finish. We turn up with the grinder and the extraction first, and the first hour is dust and noise rather than anything that looks like progress. Diamond grinding with dust extraction, flattened and profiled ready to coat.
Once the slab is open and clean we chase any cracks, fill them, and grind those flat. Then the primer goes down, and from that point the day is a sequence with cure windows in it rather than a job you can rush. We are in and out in a day on most garages, then the floor cures.
One crew, four names, and the founder on site. That is the whole company. That matters on a concrete grinding job because the person who decided the spec is the person holding the squeegee, so nothing gets lost between the quote and the floor.
Used a lot of flooring companies over the years on various jobs and lemme tell you you’re in good hands with these guys. From the quote to the finished job they were nothing short of professional.Verified review
Other systems floors we coat
The slab decides the spec.
What we find under a concrete grinding job
Moisture, contamination and surface profile are the three things that decide whether a floor lasts. Colour is the easy part and the only part most people ask about.
A lot of the slabs we open up have been sealed at some point with an acrylic nobody remembers. It reads as clean concrete until the diamonds hit it and the surface loads up. That is a full mechanical removal, not a light scuff, and it changes the day.
The system we specify
Everything we install is a system that has been tested as a system. That is the practical value of working to a manufacturer spec instead of improvising.
Polyaspartic topcoats cure faster and hold colour better under UV than standard epoxy clears. They also go down in a wider temperature window, which matters when you are working through a Mississippi summer.
Specified from the load, not a brochure.
Why the system matters more than the colour
A resin floor is four products stacked in order, and each one has a job. The primer wets into the open concrete and grips. The base coat builds thickness and carries the pigment. The broadcast layer, whether that is vinyl flake or graded quartz, gives the floor its texture and most of its wear resistance. The topcoat takes the abrasion and the UV so the layers underneath never see either.
Skip a layer and the floor still looks right on day one. It fails in month eight, usually along the door line where the sun hits or in the wheel tracks where the load concentrates. That is the difference between a coating and a system, and it is not visible in a photograph.
Grind in the morning, coat in the afternoon, walk on it that night.
What we check before quoting
Old adhesive, paint and trip-hazard high spots have to go before anything else happens.
What this floor has to put up with
This is the prep step every lasting floor depends on. Diamond grinding with dust extraction, flattened and profiled ready to coat. That combination is what we specify against, and it is why a concrete grinding job is quoted from the room rather than from a rate card.
Usually booked as the first day of a coating job. Most houses are done inside a day, then 12 hours to foot traffic.
Living with the floor afterwards
The honest maintenance answer is that there is almost none, and that is most of why people choose it.
In a commercial kitchen the cleaning routine is the maintenance plan, and the floor is specified around the chemistry you already use.
From Laurel we cover south Mississippi, the coast, coastal Alabama and St. Tammany Parish. If you are inside about a hundred miles, we will come and look at the slab. See the areas we cover.
Questions we get asked
How long does a concrete grinding job take?
Most of our residential installs are complete within a single working day.
What preparation does concrete grinding need?
Diamond grinding with dust extraction, flattened and profiled ready to coat. The honest answer about a floor comes from grinding a patch of it.
Can it take the wear this room gets?
This is the prep step every lasting floor depends on. We specify the build thickness against the actual use, not a standard sheet.
Which areas do you cover?
Yes. We cover south Mississippi, the coast, coastal Alabama and St. Tammany Parish, roughly a hundred miles out from Laurel.
Is it your own crew?
This is a family crew. Kevin founded it in 2021 and works alongside Aaron, Kyler and Averie.
Can I see the colour before deciding?
Yes. We bring the chip deck out and you pick the blend against your own light and your own walls. Colours read differently under LED, under a skylight and under a garage door that is half open, so choosing off a photograph is how people end up disappointed.
What do you find under a floor like this?
A slab that has been acid etched instead of ground has an inconsistent profile. Some areas take the coating and some do not, and you cannot tell which until it fails. We grind regardless of what was done before.
What maintenance does it need?
Do not use degreasers with high pH on a regular basis. They will dull a clear coat over time. Neutral cleaner and water handles almost everything.
What am I paying for in the build?
Thickness is specified from the load, not from a brochure. A residential garage and a forklift aisle both get epoxy, and they are not the same floor.
Talk it through with the people who will do the work.
Four names, one crew. Kevin Garner built the company in 2021 to pass it on. Serving Laurel and south Mississippi, the Gulf Coast, coastal Alabama and St. Tammany Parish. See finished floors or get in touch.